If you have written many lines and want to go to the start from some changes and modifications, you can do that by pressing the small “gg” Keyword twice. If you want to know that how many words or lines you have written on the vim editor, then you can get this information by pressing the small “g” from the keyboard and then again pressing together” CTRL “ and capital “G” 20. If the word you are looking for appears multiple times, you can go find that word again by pressing the small “n” from the keyboard. If you are looking for a specific word in your work that you have performed on the vim editor, then you can do that by typing. So, the numbers next to each line make it easy to figure out where we are on the page and where we need to go for editing by typing. If you write lots of commands and text on the vim editor, it would be difficult for you to differentiate between the lines. This function is the opposite of undo, which is used to show you the undone changes before by pressing “CTRL + R” from the keyboard. If you have made a spelling mistake or mistakenly deleted some text, you can recover that by pressing the small ” u ” from the keyboard. If you want to paste some text on the vim editor from somewhere else or from the same editor, then you can do that by pressing the capital “P,” or if you want to paste it where your cursor is, then you can do that by pressing the small “p”. If you want to cut the text rather than copy it, then you can do that by pressing the small “d” from the keyboard 14. If you want to copy the whole text, you can do that by pressing the capital “Y” key. If you have written some text on the vim editor and want to copy some specific lines, you can do that by pressing the small “y” key. If you want to select the whole line rather than some text from a specific line, you can do that by pressing the capital “V” in normal mode. If you want to select some specific part of the text, you can do that by pressing the small letter “v” below. If you are planning to delete all the lines from the vim editor, then you can do that by typing $:%d 10. The command mentioned above is there to delete the selected text only, so if you are planning to delete the whole line without selection, you can do that by pressing the small d key twice, such as “dd”. If you are in the insert mode, then you can do that by pressing the backspace key. If you want to delete anything from the editor, you can do that by pressing the “x” key if you are in normal mode. If you are in the normal mode, you can also navigate using the H,J, K, and L keys. Navigating in the vim editor is a straightforward process, all you need to do is press the “Arrow keys”. If you are working on the editor and want to save your progress but don’t want to quit it, you can do that by typing. If you are planning to quit the vim editor and want to save your progress and changes, you can do that by typing. If you want to quit vim editor without saving your progress, then you can do that by typing. If you planning to quit or exit the vim editor then you can do that by typing :quit or :q in the vim editor 4. You can switch to this mode by pressing the “ESC” key from the keyboard.Īfter the installation of the vim editor, you can open it by typing. This mode is super useful if you want to change the text you have written in the text mode. The keyword “INSERT” will be displayed at the bottom, which means you can write anything on the editor now. You can do that by typing the letter “i” on the main interface of the vim editor. If you plan to write anything on the vim editor, you should be on the insert mode for that. This is the most important step since you won’t be able to run the commands until you first install the vim editor, and you can do that by typing. This article will go through the top 25 vim commands that you can use to get the most out of this text editor. The VIM text editor also offers several useful commands that you should master to get the most out of it. It is a free and open-source text editor that runs on all major platforms with much functionality and support from the programming community. VIM application is a top-notch text editor that you may download for free. Because the Linux operating system has a command-line interface, most operations are done via commands (CLI). These hacks will not necessarily turn you into a pro with that utility, but they will ensure that you never get stuck doing the tool’s essential operations. When learning to utilize a new utility in any operating system, there are several basic hacks that you should master to use that program effectively.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |